|
What is the difference between SNMP and Syslog?
[1827]
Last Modified:
Mar 4, 2013 2:52 PM
What is the difference between SNMP and Syslog? SNMP stands for Simple Network Management Protocol and allows for remote monitoring and configuration of SNMP-capable devices on a network, while Syslog is a different protocol that can be used
|
|
|
|
What is SNMP?
[1826]
Last Modified:
Mar 4, 2013 2:51 PM
What is SNMP? SNMP stands for Simple Network Management Protocol. SNMP allows SNMP-capable devices on a network to be monitored and configured remotely. SNMP also allows these devices to report events through the use of SNMP traps. For more
|
|
|
|
E-5D: Why are my combination temperature/humidity sensors reading different humidity values?
[1825]
Last Modified:
Feb 13, 2024 11:28 AM
E-5D: Why are my combination temperature/humidity sensors reading different humidity values? If you have two or more sensors reading different humidity values, the most likely cause is that the temperature values are different for each sensor.
|
|
|
|
E-5D: Can the E-5D ping traffic on a 10.x.x.x network and send emails to 153.x.x.x mail relay server?
[1824]
Last Modified:
Feb 7, 2018 11:19 AM
E-5D: Can the E-5D ping traffic on a 10.x.x.x network and send emails to 153.x.x.x mail relay server? Yes. If the E-5D is on the 10.x.x.x network, it can ping any device on the network and send emails to the 153.x.x.x mail server relay. A
|
|
|
|
E-5D: Can I adapt communications between the ENVIROMUX-5D and a Gigabit network switch?
[1823]
Last Modified:
Feb 7, 2018 11:19 AM
E-5D: Can I adapt communications between the E-5D and a Gigabit network switch? Yes. Most Gigabit switches are 10/100/1000 compatible. When you connect the E-5D to a Gigabit network, the network will configure that port to 100 Mbit speeds.
|
|
|
|
E-5D: How do I configure the E-5D Web Interface to support HTTPS/Port 443?
[1822]
Last Modified:
Feb 7, 2018 11:19 AM
E-5D: How do I configure the E-5D Web Interface to support HTTPS/Port 443? The E-5D is already configured to support HTTPS/Port 443. To connect to the E-5D using HTTPS/Port 443, change the URL of the browser to HTTPS E.g.:
|
|
|
|
E-5D: How to Setup SNMP Traps
[1803]
Last Modified:
Feb 8, 2024 6:03 PM
E-5D: How to Setup SNMP Traps Access the web interface and go to Administration > Network. Enable the proper SNMP Agent type (v1/v2c, v1/v2c/v3, or just v3) depending on what type of SNMP browser you use. v1/v2c: no security required
|
|
|
|
E-5D: How to Setup Email Alerts
[1802]
Last Modified:
Feb 8, 2024 6:02 PM
E-5D: How to Setup Email Alerts On the web interface, go to Administration > Enterprise Settings and enter a valid email address. Your SMTP server needs to be able to recognize the sender of the message. Next, go to Network Configuration
|
|
|
|
E-5D: How to Use Smart Alerts to Inhibit Motion Sensor When Entering a Room Using a Keypad
[1723]
Last Modified:
Feb 8, 2024 5:51 PM
E-5D: How to Use Smart Alerts to Inhibit Motion Sensor When Entering a Room Using a Keypad This entry explains how to create an installation where an installed motion sensor will not trigger an alarm when an operator enters and is within
|
|
